Restore your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may want to reinitialize your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the settings or are experiencing unexpected behavior. Fortunately, resetting your Holosun is a easy process that can be performed in just a few steps.

• First ensuring your red dot sight is turned on.
• Locate the small reinitialize button on the side of the sight.
• Use a small object to activate the reset switch for approximately three moments.
• Let go the lever and your Holosun EPS Carry Red Dot sight will power cycle.
• The red dot sight should now be reverted to its factory settings.

Return to Your Holosun EPS Carry Red Dot toward Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to go back to basics, resetting it to its factory configuration is a breeze. First, determine the tiny button on the bottom of your optic. Then, press and hold it for around ten seconds until you see a brief flash. Your Holosun EPS Carry is now returned to its factory settings, ready for accurate shooting.

Bring Your Holosun EPS Carry Back to : Functionality

Is your beloved Holosun EPS Carry experiencing some performance problems? Don't despair! A simple factory reset can often fix the problem and get your red dot sight back to its former glory. Before you begin, remember to detach the battery from your Holosun EPS Carry to prevent unexpected activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these simple steps:

• Simultaneously press and hold the power button for approximately 5 seconds.
• A message will flash, indicating that the reset is in progress.
• Let go of the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can connect the battery and test your sight's functionality. If you encounter any further problems, don't hesitate to contactsupport team.

Revert Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases more info all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Follow these steps carefully to ensure a successful factory reset.

• First, Turn on your Holosun EPS Carry by pressing the power button.
• Next, press and hold both the mode button and the up/down adjustment button simultaneously.
• As you continue holding these buttons, tap the power button once.
• A message will show a confirmation prompt indicating that the reset process is initiated.
• Permit the process to finish. This may take a few moments. Once done, your Holosun EPS Carry will automatically power off.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Reset All Settings on Your Holosun EPS Carry

To Factory reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Holding a specific button combination. Consult your Instruction for the exact button sequence for your model. Once in the settings menu, look for an option that says "Clear Settings". Select this option and confirm the reset. Your sight will then power off and restart with all settings Restored to their default values.

Reset your Holosun EPS Carry with a Factory Default Settings

If your Holosun EPS Carry is acting up, a factory reset might be the answer. This will set back your sight to its initial settings, clearing any personalized configurations you've made. To accomplish this reset, follow these easy steps:

• To begin, identify the reset switch on your EPS Carry.
• Secondly, engage a small object, like a pen tip, to activate the reset switch.
• While keep the reset switch engaged, activate your EPS Carry.
• You'll blink a message indicating that the reset is finished.

When the reset is complete, your EPS Carry will be back to its factory settings.

Report this wiki page